Camera test checklist
Alpha12 camera checks
The alpha10 camera report records a restart on the Color Filter page.
The owner confirmed that alpha11 resolved the restart and CP icon defects and reports that alpha12 fixes the remaining filter graphic issue. Alpha12 camera findings.
For the alpha12 check, verify the installer gives package SHA-256
cddd7a1f1320e7680bec9e8430e25c69857c2f4bf764e571d6bfffb775acd3fa. After the startup checks (steps 0–3 below),
do step 19 first. If the camera restarts or freezes, stop the checklist, record what happened and follow
stock recovery.
| Step | Do | Expect |
|---|---|---|
| 19 | Open Monochrome Profile 1 › Color Filter. Turn both dials. Cycle the filter dial through all values, change the level, then leave and re-enter. Check Profile 2 separately. Take a red-filter and a blue-filter JPEG of the same scene. | The page opens and stays open. The header names each filter through the wrap. The two filters render colours differently in the JPEGs. The other dial changes +n. Both values persist after re-entry, and Profile 2 keeps its own values. The ring marks the selected swatch. The centre follows the selected colour and is grey for None. The stock “Vivid” word stays visible. |
| 16 | Tick ND32 and ND64 in CP Button Settings. Hold CP and turn the dial past ND16. Select each, then untick them and repeat. | ND32 and ND64 each show their own icon when offered. Selection gives the matching shooting label and exposure. Unticked items disappear. |
| 20 | After a half-press, untick every CP item except ND32. Hold CP, then repeat with only ND64 ticked. | Each item can be offered, shows its icon and can be selected when it is the only item ticked. |
| 15 | Color Profile 1 › Shading. Turn the dials in both directions and re-enter the screen. | Green knob and a setting that steps and persists. |
| 17 | Check Monochrome Profile 1's Film Grain row and strip, and the Color Filter sidebar row. | Off / Low / Std / High artwork, with visible grain in pictures, and a Filter sidebar icon. |
| 18 | In Color Profile 1 set Daylight with an A/B shift. In Color Profile 2 set Shade. Revisit both profiles and Natural. | Each profile restores its own WB and shift. Natural keeps its own WB. |
Baseline startup and regression checks
The alpha8 camera report records the successful boot and known UI defects. If the camera fails to start or freezes, follow stock recovery and report what happened.
Before step 1, set Picture Mode to Natural in OM's firmware for the shooting mode the camera will start in (and in Movie mode if you use it). Earlier test builds may have left a Color Profile stored there. Alpha8 activates profiles at the first shutter half-press after switching on and repairs stale profile numbers then.
| Step | Do | Expect | Shows |
|---|---|---|---|
| 0 | Flash OM's own 1.1 from card/restore (hold OK, switch on). |
Steady light, then blinking; a normal start. | Your card, your timing and the card update work, before anything is changed. |
| 1 | Flash card/DCOLYMP/E1489999.BIN. No OM5MOD folder on the card yet. Switch on. Do not touch the shutter button. |
The normal shooting screen. Menu, playback and the super control panel work. | The changed program loads and starts. Nothing of ours is active before the first half-press. |
| 2 | OK › Picture Mode. Move along the list without a half-press first. | Color Profile 1–3 and Monochrome Profile 1–3 are in the list, after Color Creator. Selecting one works; before a half-press their colour and tone pages do not appear and the trash button does nothing. | The tables and screens. This is where the third build froze. |
| 3 | Switch off, on. Half-press once. Take a photo in Natural. Play it back. | A normal photo. | Arming (one small block of memory is taken at the first half-press). |
| 4 | Picture Mode › Color Profile 1 › the colour wheel. Press the trash button. | Saturation → Hue → Lightness. On alpha8 the header and dials work with the wheel graphic missing. Check a strong Hue and Lightness change against Natural. | The editor and that Hue / Lightness reach the photo. |
| 5 | Switch off, on, several times; leave it on Color Profile 1 while you do. | It starts every time, still on Color Profile 1 with your values. | Starting with a profile saved: the suspected cause of the loop after the third failure. |
| 6 | Copy OM5MOD (with LOOKS.BIN) to the card. Switch on, half-press, Picture Mode › Color Profile 1, press the trash button (highlight on the strip of picture modes). |
The title changes to the first look's name at once; its values are in the rows. A second press gives the second look's name. | Films. |
| 7 | Take the card out, put another in, switch off and on. | Color Profile 1 still has the look and its name. | The look lives in the camera. |
| 8 | Live ND: ND32 and ND64, on a tripod. Custom modes C1–C4 with a Color Profile. Monochrome Profile 1. | They work. | The rest. |
Alpha9 additions
The owner confirmed that alpha9 (package 2e9777ce…fbc50) boots. After the alpha12 checks and baseline checks, repeat:
| Step | Do | Expect |
|---|---|---|
| 9 | Picture Mode carousel, sidebar and super control panel on Color 1–3 and Monochrome 1–3. | Numbered icons (1/2/3, M1/M2/M3), no overlap when scrolling the sidebar. |
| 10 | Change any setting of Color Profile 1, confirm, return to the shooting screen. Repeat for one Monochrome Profile, and after loading a look. | The profile's icon stays on the shooting screen (alpha8 and earlier candidates lost it). |
| 11 | Tone Curve row: change Shadows, Midtones and Highlights through several values. | An icon in every state, matching the curve's direction. |
| 12 | Colour wheel and tone curve pages. | The wheel and curve draw, and redraw after leaving and re-entering. Note any colour or flicker problem. |
| 13 | Keep using the wheel, Tone Curve and trash look cycling for over 10 s; then leave the screen idle. | The screen stays open while used and closes about 8 s after the last action. |
| 14 | Gear menu › CP Button Settings; hold the CP button; Live ND menu. | ND32 and ND64 listed, switchable and kept after a power cycle; ND32-LV / ND64-LV labels and their exposure. |
Steps 1 to 3 are the dangerous ones. If step 1 fails, the build is wrong in a way the emulator cannot see, and nobody else should flash it.